Bleeding time
Bleeding time measures how long it takes for bleeding from a small, standardised skin puncture to stop. It assesses the first phase of stopping bleeding, which depends on the platelets and the blood vessel wall, and is used as a first-line screening test, most often before surgical and dental procedures.
Preparation and sampling
- Preparation
- Guide to preparing for tests
- Sample
- Blood
- Results available in
- 1 working day
- Where it is done
- All laboratories and map
Description
About the test
When a blood vessel is damaged, bleeding is stopped in several stages (haemostasis). In the first stage, primary haemostasis, the vessel constricts and platelets stick to the site of injury and to each other, forming a ‘plug’ that seals the wound. Von Willebrand factor, a protein that helps platelets attach to the vessel wall, plays an important part in this. Clotting factors then come into play and reinforce the plug with fibrin.
Bleeding time is a simple test of primary haemostasis: a small, standardised puncture or cut is made in the skin and the time until the bleeding stops is measured. The most common methods are the Duke method, with a puncture on the earlobe or fingertip, and the Ivy method, with a shallow cut on the forearm while a blood pressure cuff is inflated to 40 mmHg. Every 30 seconds the drops of blood are blotted with filter paper, without touching the wound itself, until the bleeding stops.
A prolonged bleeding time may point to a low platelet count, a platelet function disorder, von Willebrand disease or the effect of medicines such as aspirin. However, the test is sensitive to the way it is performed, and a normal result does not reliably predict bleeding during surgery. It is therefore interpreted together with the platelet count, clotting tests and any history of bleeding.
When it is recommended
- As a screening test before surgical procedures, for example before removal of the tonsils or a tooth extraction, as advised by your doctor;
- A tendency to bleed: bruising easily, frequent nosebleeds or bleeding gums, heavy periods, prolonged bleeding after cuts, tooth extractions or operations;
- Suspected platelet function disorder or von Willebrand disease;
- Known clotting disorders or a tendency to bleed in the family.
Preparation
- Tell your doctor and the laboratory staff about all the medicines you take, especially aspirin (acetylsalicylic acid), painkillers and anti-inflammatory medicines (such as ibuprofen or diclofenac), medicines that stop platelets sticking together (such as clopidogrel) and anticoagulants. These medicines can prolong the bleeding time, and the effect of aspirin lasts 7–10 days after the last dose.
- Do not stop any medicine on your own, only in agreement with your doctor.
- Also tell the staff about supplements such as fish oil (omega-3 fatty acids) or ginkgo, as these can also affect the result.
- No fasting is needed for this test. If you are also having blood tests, follow the general laboratory rules: blood is taken in the morning, between 7 and 10 a.m., after 12 hours of fasting (you may drink water as usual); do not take vitamin supplements the day before, and avoid strenuous physical exercise for 2 days beforehand.
Sample
No blood is collected into a tube: the test is performed directly on the patient, with a small skin puncture (usually on the earlobe or fingertip) or a shallow cut on the forearm, depending on the method.
Reference values
- Duke method: approximately 1–3 minutes.
- Ivy method: approximately 2–7 minutes (up to about 9 minutes, depending on the technique).
Reference values depend on the method and the laboratory; the values printed on your report apply to your result.
Interpreting the results
A prolonged bleeding time may indicate:
- a low platelet count (thrombocytopenia);
- a platelet function disorder, inherited or acquired (for example in severe kidney failure or liver disease);
- von Willebrand disease;
- the effect of medicines: aspirin, non-steroidal anti-inflammatory drugs, antiplatelet medicines and, in higher doses, anticoagulants;
- a marked fibrinogen deficiency;
- diseases of the blood vessels and connective tissue that make the vessels more fragile;
- severe anaemia.
A normal bleeding time does not completely rule out a mild disorder of haemostasis. In clotting factor deficiencies, such as haemophilia, the bleeding time is usually normal, so these disorders are detected with other tests (PT, aPTT, clotting factors).
Your doctor interprets the result together with your symptoms and other findings.
What can affect the result
- How the test is performed: the site and depth of the puncture, the cuff pressure, touching the wound with the filter paper;
- Skin temperature and thickness, and the blood supply to the puncture site;
- Medicines that affect platelets or blood clotting (aspirin, non-steroidal anti-inflammatory drugs, clopidogrel, anticoagulants, some antidepressants);
- Supplements such as fish oil or ginkgo, and alcohol;
- The platelet count and severe anaemia;
- Age: in older people the skin is thinner and less elastic, which can affect the result.
Related tests
- Full blood count with platelet count – the platelet count is key to interpreting the bleeding time;
- Clotting time – a basic test of blood clotting, often done together with the bleeding time;
- Prothrombin time (PT, INR) and activated partial thromboplastin time (aPTT) – to assess the clotting factors;
- Fibrinogen – a protein essential for clot formation;
- Von Willebrand factor and factor VIII – when von Willebrand disease is suspected;
- Platelet function tests (for example PFA-100, platelet aggregation) – more precise tests of primary haemostasis.
Frequently ordered together
How to order tests online?
Choose the tests you need and add them to your cart. Use the site search to find the tests you want more easily.
Payment method:
- Online – payment uses 3D-Secure, a secure authentication protocol that minimises the risk of fraud.
- At the laboratory – order your tests online and pay for them when you come to the laboratory.
After payment, you will receive an email confirming your order, with details of how to prepare for sampling. From then on, you can go to the Sante laboratory you chose when ordering your tests and have your samples taken.