Guide to patient preparation for laboratory tests

When preparing for laboratory tests, please follow these recommendations:

BLOOD SAMPLES

Recommendations: For most tests, blood is normally collected between 7 and 10 in the morning, after a 12-hour fast and a night’s rest. If you are taking medication, the blood sample is taken before you take your next dose.

Some tests require a special diet or the avoidance of certain foods and drinks on the day before your blood is taken, because these affect the results. Please therefore contact the laboratory for precise information on how to prepare for testing.

Taking vitamin supplements can also affect the results, so you should stop taking them 1 day before blood sampling.

It is advisable to avoid strenuous physical exertion for 2 days before testing.

In acute conditions, samples for urgent tests such as a full blood count or C-reactive protein, and for hormones (e.g. cortisol, progesterone), may be collected as instructed by your doctor.

Important:

If you are taking medication, always consult your doctor to determine whether treatment should be stopped before samples are taken, and inform the laboratory staff.

If you are having tests to check the effect of a treatment, a certain amount of time must pass between starting the medication and testing. In that case, ask your doctor when you should be tested.

URINE SAMPLES

Important: Immediately before urinating, wash your hands and genital area thoroughly with soap and water, and dry with a clean towel or paper towel. Take the urine container out of its bag and open it at the moment you begin to urinate. Do not touch the inside of the lid or the container with your fingers. Pass urine into the toilet for the first few seconds, then place the container in the stream and collect the rest of the urine in it. It is enough for the urine container to be 2/3 full. Try to take the sample to the laboratory within the next 2 hours, and keep it in a cool place until then. If a urine sample is left at room temperature for longer, its components break down and bacteria multiply, so the result you receive is not reliable. Avoid collecting urine samples immediately before, during and immediately after menstruation. The same applies if you have bleeding haemorrhoids.

Special instructions:

Urinalysis with sediment analysis – you need to fill 2/3 of the urine container. Use a midstream sample of the first morning urine.

Urine culture – the sample for urine culture is given before starting antibiotic treatment, or 7 days after the treatment has finished in order to check whether it has been successful. If you would like both urinalysis with sediment analysis and a urine culture, both can be done from the same sample, provided it has been collected correctly. It is important to use a sterile urine container (a cup with a lid in a sealed bag), which you can buy at a pharmacy or obtain from the laboratory. The sample is collected in the same way as for urinalysis with sediment analysis. A midstream sample of the first morning urine is used, after washing the genital area.

24-hour urine collection: for certain urine tests, a 24-hour urine sample must be collected. Special containers for this are available from the laboratory. Before you start collecting urine, find out whether you need to avoid certain foods and drinks on the day before and during collection, and whether a preservative is needed. A preservative is a liquid (an acid or a base) that is added to the container during 24-hour urine collection when certain urine parameters are tested. The preservative is also provided by the laboratory.

Begin the 24-hour urine collection in the morning by emptying your bladder completely into the toilet. Note the time. Then pass every subsequent portion of urine into the 24-hour urine container. Keep the container in a cool place throughout the collection. You finish the collection the next day at approximately the same time as you emptied your bladder the previous day, except that this time you pass that sample into the container. Bring the collected urine to the laboratory without delay. During the 24-hour urine collection, make sure that every individual portion of urine goes into the container, as this affects the final volume and the value of the result.

Collecting urine from babies and children who do not yet control their urination – use a sterile urine collection bag, which can be bought at a pharmacy. Use the bag according to the enclosed instructions. For children, as for adults, the genital area must be washed and dried well before urine is collected, and then the bag applied. The bag should not be left in place for more than an hour. If no urine has been collected within an hour, apply a new bag and discard the previous one. After the urine has been collected, transfer the contents of the bag into a sterile urine container and take it to the laboratory.

THROAT SWAB

Important: A throat swab is taken in the morning before you brush your teeth or have breakfast, and before starting antibiotic treatment or at least 7 days after you finish treatment. Taking a throat swab during antibiotic treatment can lead to false-negative results.

NASAL SWAB

Important: Avoid using nasal preparations and cleaning your nose before the sample is collected. Have the sample taken before starting antibiotic treatment or 7 days after the end of treatment.

STOOL SAMPLES

Tests: stool culture, Giardia antigen, Helicobacter pylori antigen, faecal occult blood, Campylobacter antigen

Important: For stool sampling, use a sterile container with a cap that has a small spoon on the inside for taking the sample. When taking the sample, choose parts where mucus is visible or parts streaked with blood. Do not take more than 4-5 spoonfuls per sample. Collect the sample before you start treatment or before using suppositories. Ideally, hand samples in to the laboratory immediately after collection, or ask about the stability of the sample, which varies depending on the test being performed. Keep samples in a cool place until you bring them to the laboratory.

VAGINAL/CERVICAL/URETHRAL SWAB

Detection – Chlamydia trachomatis, Mycoplasma / Ureaplasma, human papillomavirus (HPV), Pap test.

Tests: culture from a vaginal/cervical/urethral swab, Chlamydia trachomatis, Mycoplasma/Ureaplasma, HPV, Pap test.

Important: Avoid sexual intercourse, douching, the use of tampons and intravaginal treatments for 48 hours before the sample is collected. Ideally, have samples collected mid-cycle, before or after treatment of the infection. Samples should not be taken during antibiotic treatment, as the results may be false negative.

SEMEN SAMPLES

Container – use a sterile urine container to collect the semen sample.

Tests – semen culture, semen analysis, sperm DNA fragmentation testing, PCR testing for infectious agents in semen

Quantity – for semen analysis and sperm DNA fragmentation testing, the complete ejaculate must be collected. Take the sample to the laboratory within 30-45 minutes, keeping it at approximately 37°C. Ideally, the sample should be produced at the laboratory.

Delayed transport, an unsuitable transport temperature, a non-sterile container or an incomplete ejaculate may lead to unreliable results.

Recommendations:

  • Abstain from ejaculation for 3-7 days.
  • Avoid medication for a week before providing the sample, if possible.
  • Wash your hands and genitals thoroughly before collecting the sample and dry them with a towel.
  • Do not provide a sample for semen analysis or sperm DNA fragmentation testing if you have a cold.
  • Abstinence is not necessary for semen culture and PCR tests. The tests are performed before starting treatment or 7 days after it has ended.
Back to top